公司新聞
挖掘機的各種操作使用技巧
來源：http://ywsun168.com/ 日期：2022-12-16
很多朋友在使用挖掘機的時候積累了豐富的經驗，對于挖掘機的操作都有自己的一套技巧，但同樣如此，每個人的技巧本質都是一樣的。濟南挖掘機租賃廠家今天給大家介紹一下挖掘機的各種操作使用技巧，歡迎廣大機友發言指導。
Many friends have accumulated rich experience when using excavators. They have their own set of skills for the operation of excavators, but the same is true for everyone. Today, Jinan excavator leasing manufacturer will introduce various operation skills of excavator to you. Welcome to speak and guide.
1、運營技術
1. Operational technology
檢查周圍的情況。轉彎時注意周圍障礙物和地形，安全操作；操作時，請確認履帶的前后方向，以免傾翻或撞擊；挖掘方向盡量不要對著終傳動，否則容易損壞行走馬達或軟管；工作時保證左右履帶與地面完全接觸，以提高整機的動態穩定性。
Check the surroundings. Pay attention to the surrounding obstacles and terrain when turning, and operate safely; During operation, please confirm the front and rear direction of the track to avoid tipping or impact; The excavation direction shall not be toward the final drive as far as possible, otherwise the traveling motor or hose may be damaged easily; During operation, the left and right tracks shall be fully contacted with the ground to improve the dynamic stability of the whole machine.
2、有效的挖礦方法
2. Effective mining methods
當鏟斗油缸與連桿、斗桿油缸與斗桿成90度時，挖掘力大；當斗齒與地面保持30度夾角時，挖掘力好，即切土阻力??；挖掘斗桿時，確保斗桿角度在前面45度到后面30度之間。同時使用動臂和鏟斗可以提高挖掘效率。
When the bucket cylinder and the connecting rod, and the stick cylinder and the stick are at 90 degrees, the digging force is large; When the bucket teeth keep an angle of 30 degrees with the ground, the digging force is good, that is, the soil cutting resistance is small; When digging the stick, make sure that the stick angle is between 45 degrees in the front and 30 degrees in the rear. Using the boom and the bucket at the same time can improve the efficiency of digging.
3、挖石頭
3. Rock digging
使用鏟斗挖掘巖石會對機器造成很大損壞，應避免使用；需要挖掘時，應根據巖石的裂縫方向調整機體位置，使鏟斗能夠順利鏟入挖掘；斗齒插入巖石裂縫中挖掘時，利用斗桿和鏟斗的挖掘力進行挖掘（注意斗齒打滑）；未破碎的巖石應先破碎，然后用鏟斗挖掘。
The use of bucket to excavate rocks will cause great damage to the machine, so it should be avoided; When it is necessary to excavate, the position of the machine body shall be adjusted according to the direction of the rock crack, so that the bucket can be smoothly shoveled into the excavation; When the bucket tooth is inserted into the rock crack for excavation, use the digging force of the stick and bucket for excavation (note that the bucket tooth slips); Rock that is not broken shall be broken first and then excavated with bucket.
4、斜坡平整工作
4. Slope leveling
進行平面修整時，應注意將機器平放在地面上，以防止機身晃動。掌握動臂和斗桿動作的協調性很重要，控制兩者的速度對于飛機配平很重要。
During plane trimming, the machine shall be laid flat on the ground to prevent the machine body from shaking. It is important to master the coordination of boom and stick movements, and it is important to control the speed of both for aircraft trim.
挖掘方法_文本挖掘方法有哪些_挖掘機的操作方法
Excavation method_ What are the methods of text mining_ Operation method of excavator
5、加載作業
5. Load Job
機體應處于水平且穩定的位置，否則難以準確控制轉動和卸荷，從而延長工作循環時間；車身與貨車應保持適當距離，防止車身尾部在180度旋轉過程中與貨車相撞；視野開闊，工作效率高，同時需要正確把握旋轉角度，減少轉彎時間；車位低于挖掘機，縮短動臂提升時間，視線好；先裝載沙子、碎石，然后放置大石塊，這樣可以減少對車箱的沖擊。
The machine body should be in a horizontal and stable position, otherwise it is difficult to accurately control the rotation and unloading, thus extending the working cycle time; The vehicle body and the truck shall be kept at a proper distance to prevent the rear of the vehicle body from colliding with the truck during 180 ° rotation; Wide vision, high working efficiency, and correct rotation angle to reduce turning time; The parking space is lower than the excavator, shortening the boom lifting time and providing good visibility; Load sand and gravel first, and then place large stones to reduce the impact on the car body.
6、在柔軟區域或水中工作
6. Working in soft areas or water
在軟土地區作業時，應了解土體松動的程度，注意限制鏟斗的挖掘范圍，以防發生滑坡滑坡和車身深沉等事故。在水中作業時，應注意車體允許的水深范圍（水面應低于載體中心輪）；如果水平面較高，回轉支承內部會因進水而潤滑不良，發動機風扇葉片受水沖擊造成損壞，電路元件短路或開路-因進水而循環。
When working in the soft soil area, it is necessary to know the degree of soil looseness, and pay attention to limiting the excavation range of the bucket to prevent accidents such as landslide and vehicle body sinking. When working in water, pay attention to the allowable water depth range of the vehicle body (the water surface should be lower than the center wheel of the carrier); If the horizontal plane is high, the slewing ring will be poorly lubricated due to water inflow, the engine fan blades will be damaged due to water impact, and the circuit components will be short circuited or open circuited - circulating due to water inflow.
此外在使用挖掘機進行吊裝作業時，應確認吊裝現場的周邊情況，使用高強度吊鉤和鋼絲繩，吊裝過程中盡量使用專用吊裝裝置。更多相關內容就來我們網站http://ywsun168.com進行咨詢吧！
In addition, when using excavators for hoisting operations, confirm the surrounding conditions of the hoisting site, use high-strength hooks and wire ropes, and try to use special hoisting devices during hoisting. More relevant content will come to our website http://ywsun168.com Consult!
公司地址：濟南市商河縣賈莊鎮民營經濟創業園
公司名稱:永誠廣建公路材料（山東）有限公司 
備案號：